razorlife.png

Every Schenk Knife comes with a “RazorLife” warranty. Your knife will be re-sharpened to a full factory edge, including a leather strop and hone (this service does not apply to serrations). If that razor edge has been lost because of heavy use or neglect, ship your knife for inspection, cleaning, and re-sharpening. Please allow 2-5 business days for return. There is no return shipping cost for this service. 

Securely ship your knife with postage paid and insured. Schenk Knives is not responsible for any product lost in shipping. Any questions regarding the Schenk Knives “RazorLife” warranty please contact us by email or phone.

SCHENK KNIVES
Attention: RazorLife
4570 N. Haroldsen Drive
Idaho Falls, Idaho 83402
info@schenkknives.com

Each knife that is sharpened at our factory goes through a 5-step process to ensure that each knife has a razor sharp edge when it leaves our factory.

 

 

accutraction300px.png

Accu-traction was developed from years of hunting experience. Accu-traction is placed on the tip of certain hunting models that can accommodate a forward grip which allows you to place your index finger on the tip of the knife. Accu-traction helps in two areas-first it helps give your index finger extra traction while often times covered in blood and making the tip of the knife slippery; and second, purpose is to allow you to find the point of your knife, without cutting yourself, even when you can’t see the knife in your hand.

 

MID TECH | HANDCRAFTED

usa-made.png

Coming soon.

 

STEEL

Coming soon.

 

BLADE GRINDS

HOLLOW GRIND - A hollow grind is commonly used in today's production knives. The grind is highly favored by hunters and sportsmen for its razor sharp edge and its versatility in skinning and butchering meats after a hunt. A hollow grind reduces knife edge thickness and is a very sharp but also is more prone to rolling or damage when put under heavy cutting.

FLAT GRIND - A flat grind has a stronger edge due to the greater thickness behind the sharpened edge.  Re-sharpening thickens the edge faster and  it takes a bit longer to re-sharpen. A great choice for general heavy use.

CONVEX - A convex grind is very strong with a well-supported cutting edge for heavy duty use and cutting.  Edge thickens directly behind the sharpened edge. With heavy use and over time the blade edge will begin to thicken and become harder to re-sharpen. A great choice for heavy duty use.

SCANDI - A scandi grind has the strongest blade edge. The scandi grind is popular among survival and bushcrafting groups. When ground correctly, it allows for a true zero degree edge. Although this blade edge is strong and easy to re-sharpen, it does dull faster than other blade grinds.

 

HEAT TREATING

SALT BATH FOR DAMASCUS AND 52100 STEELS - Salts are heated to a molten 1500 degrees. The knife blade is lowered into the salt bath and soaked, then quickly removed, agitated and quenched in low temperature molten salts for 1 min. The blades are removed from the low temperature salts, and while still soft, straightened if needed. The blade is then placed back into low temperature salts or a heat treating kiln and allowed to soak at lower temperature for several hours. This tempering process removes much of the internal stress in the steel and tempers or slightly softens the blade to a perfect state to hold a great edge and not be too brittle.

When the process is done in salt baths it will yield a blade that is approximately 20% tougher, has greater edge holding ability, and no hardening scale to remove from the high temperature hardening process.   

This process is done in house and for O.E.M. customers  around the country.

ELMAX STAINLESS POWDERED STEEL -The blades are placed in a vacuum high temperature heat treating kiln. The blades are soaked at a temperature around 2000 degrees F. Within the kiln the blades are quickly cooled and become very hard.  The blades are then reduced to minus 320 below zero (cryo quenched), held for a period of time and brought back to room temperature where they are tempered at a low temperature for several hours. Our Elmax is sent to Peters Heat-Treating who we feel is the best in the industry for heat-treating Elmax.

 

KNIFE HANDLES

G-10A composite made of layers of glass cloth and epoxy resin.  It can then be colored if desired.  It is then compressed and baked.  The resulting material is very hard, lightweight, strong and attractive.  Our top choice for a using on production knives.

MICARTA - A composite made of layers of cloth, paper or canvas and phenolic resin. Micarta is a very tough and durable material that makes for a great choice for an economy priced knife handle.

RARE WOODS - We use most any wood but prefer to use stabilized domestic burls, that we harvest and stabilize in-house, such as: box elder, maple, California buckeye, black ash, redwood, walnut and many others. Stabilizing is a process whereby the burl has been dried then processed using a combination of vacuum, liquid epoxy resins and curing.  The dead air space in the wood has now been replaced by cured epoxy resins.  To finish the handle you sand to 600 grit then buff on a pink compound.  This is one of our favorite handle materials to use on custom edition and limited edition knives.

MISC. HANDLE MATERIALSWe commonly use axis stag, elk antler, deer antler, moose antler, bones, fossil ivory, water buffalo horn, mammoth ivory, giraffe bone and many other exotics materials.

 

KNIFE SHEATHS

LEATHER - We make all leather sheaths in house using domestic saddle skirting from Wickett & Craig.  Leather can be carved, tooled and stamped. All knife sheaths are glued, stitched, assembled, wet formed, dyed, oiled and finished giving each Schenk Knife a custom, handcrafted leather sheath.

KYDEX - A thermoforming plastic that is used on many tactical knives, neck sheaths, hunting knives, and divers knives.  Many colors and texture patterns are available.  Kydex sheaths are generally  held together with screws and rivets and need steel parts for belts clips and other fittings.

TACTICAL/MILITARY - This style of sheath can be a combination of kydex, plastics, leather and nylon fabrics.  Military looking and loaded with clips and attachment devices.

 

DESIGNS

Coming soon.